Free shipping on Die Sets to UK and Europe! Questions to info@pelletpressdies.co.uk

Die Set FAQs

Using your Die Set:

What is the max load for my die? You can find the max recommended load on the individual product page. The steel we use has a very high yield strength of over 80,000 psi or 550 MPa. We recommend a 50 % safety margin, loads for each die set should be carefully considered before using the die to ensure safe operation. This is of particular concern with the smaller ID dies where you can reach the yield strength of the steel with a few pumps of the hydraulic press. Do note that using high pressing force does not guarantee a denser pellet. If you press too hard, you will most likely surpass the fracture stress of the compact well before you reach the yield stress of the material. The stress in your pellet will concentrate at the top side of your pellet and you will likely see cracking or "capping" at the top of your powder compact.

Do I need the prepare the die set in any way? We store our dies with a water resistant lubricant. When you get it, just give it a good clean with detergent before use. If you are storing your die for a long time or it will be exposed to moisture or humidity then you can simply spray with WD-40 or a similar product before storing.

Can I heat up my die set? Our standard die sets cannot be heated as the metal has been heat treated, heating it at all will compremise the heat treatment, making it softer, weaker and quickly lead to oxidisation. As an alternative we can make you a custom die set out of stainless steel that could be heated to around 250 °C (480F).

 What is the thickest pellet I can make with my die set? As a general rule of thumb your pellet height should not greatly exceed the diameter of your pellet. This is because you get non-uniform compaction through the pellet when you go thicker than the diameter, the top will get more stress concentration than the bottom (non-moving surface). That being said, all materials are different, so you can take this rule with a pinch of salt.  The maximum height of pellets you can make using our standard range (50mm height die sleeve) die sets would be between 15-25mm pending on the material you are pressing and method of loading the die set.

Tips

  1. If you’re pressing long pellets (with respect to your diameter), consider lubricating your die.
  2. Try adding a rubber o-ring (or something flexible) between the base plate and the die sleeve, this will allow movement of both he top and the bottom plunger, improve the stress uniformity through the pellet.
  3. For making very long aspect ratio pellets there are other methods such as isostatic pressing which might be more suitable

What height opening does my press need to be? For our standard range have a 50mm height die sleeve and similar length plunger. Your press will need about 100-125 mm (4-5 inches) clearance for loading the die set depending on how full of powder your sleeve is a where you are using spacers.

 

Can I use organic solvents with my die set? Organic Solvents cannot be used with our standard die sets. We can make a custom stainless steel die set but you would need to check that the solvents you are using would be compatible with a 400 series stainless steel.

 

Do I need to use lubricants or binders? You do not need to lubricate your die before use for most materials nor do you have to use binders. Some people like to use a small amount on lubricant on the walls of the die as this is where there is highest friction during pressing and release which can lead to cracking. Likewise, some applications and materials use binders as common processing protocol. Both lubricants and binders can be burned out afterward when sintering above 700 °C leaving behind minimal residual residue (carbon).

Will my die rust? The steels we use for our standard die sets are high strength and high hardness and typically the steel of choice for the most demanding tooling applications – they are not stainless steels. If you don't dry it after washing or store it wet - yes it will rust. Don't worry, it happens - the good news is that it should be easy to clean off. If you so want us to make a custom die in stainless, we can do it - just send us an email.

How do I clean and store my die set? After each use make sure die set is cleaned and dry. If you are storing your die for a long time or it will be exposed to moisture or humidity then you can simply spray with WD-40 or a similar product.

I scratched the inside of my die sleeve or rod. Can I fix this? Potentially, yes. For small scratches you can purchase a cylinder flex hone tool (http://www.brushresearch.com/brushes.php?c1=1), attach it to a drill and clean the inside of your die sleeve or rod with some honing oil. You only need to be worried about removing the high points from the scratch that are causing interference. If the scratches are on the end they might be removed with a fine file or paper. If you use something rough, you will never get the finish back and if you remove more than 0.01mm and you will notice the difference in the fit. 

Do you have some advice for making good pellets?
There is a lot to say here...

  1. Number 1 - obviously - press safely, if unsure ask someone with experience. You are able to put a lot of force through your die with a hydraulic press. Think about the force you want to apply beforehand, do not exceed the force for the die you are using, wear safety googles with side shields, use a guard between you and the press, keep other items off the press table so they don't get caught, make sure everything is inserted correctly and well located before pressing.
  2. Check that your press plates are parallel and sample as level as possible before pressing. Check your pressure and force gauge is working and know what your max pressing force/pressure will be. Check against the maximum loads on the product page for your pellet die diameter.
  3. If the die is overfilled with powder before pressing, the plunger will not locate properly.
  4. Always clean your die before use - this will not only stop contamination but make the die work better, with less friction.
  5. Higher force is not necessarily better - if you find your pellet is cracking then you should consider using less force before using more force. Please can you make sure that anyone using this die set follows the recommended forces on the product pages on our website. Make sure that the force gauge on hydraulic press is working and accurate. 
  6. Make sure the pellet you are pressing is not too long so that you don't have a lot of un-supported plunger during pressing. Ideally less than 10mm is un-sheathed out of the die set. Press without spacers if there is a lot of exposed plunger during pressing
  7. If you are having trouble with a certain material - don't worry we have all been there. Consider drying before pressing changing the grain size your materials before pressing (more grinding), tapping with a small rubber mallet after assembly and before pressing (helps the powder move around, reorganise and settle before pressing), you can also try using lubricants or binders to help get your pellet out.